Menus explained
Every panel, button and slider on the design page, in the order they sit on screen. For the steps after Render (printing, pouring, curing), see the casting guide instead.
The screenshot in the in-app help (the ? button, top right) numbers the same thirteen areas this page walks through. Use that for a quick refresher, use this page for what each control actually does.
- Header: name, length, templates, save
- Profile
- Surface
- Path
- 3D view
- Toolbox: Scale, Flatten, Etch, Shaft, Tip, Balls
- Core Cavity
- Squirt tube
- Checks
- Get the mould printed
- Render and Download
- Printer
- Quantities
- Gallery, Publish and Share link
Header: name, length, templates, save
- Name. Type a name for the design. Empty, the template name shows as a grey hint.
- Randomizer. Builds a new random design: a random template family, size, bend and a texture on about half of them. Undo brings your design back.
- Length and Fix length. Length is the total length of the shape, base to tip. With Fix length ticked, dragging the path keeps this length; untick it to let a path edit change the length instead.
- Templates. Opens a gallery of the built-in starters, each with a picture, and below them any design you saved in this browser. Click a card to load it; the gallery stays open so you can try several, and only its ✕ closes it. Drag it by its title bar. A saved design has its own small ✕ to delete it. Loading replaces the current design, but Undo brings it back.
- Save. Keeps the current design under its name, in this browser only. It then shows in Templates.
- Export JSON, Import JSON. Export downloads the design as a
.jsonfile, a way to back it up or hand it to someone else. Import loads one back in. - Undo, Redo. Step back and forward through edits: profile and path changes, Surface, Flatten, Shaft/Tip/Balls texture, Etch, Scale, template loads and Randomizer all count as one step each.
- Help (?) and Guide. The ? button opens a numbered screenshot of this same page. Guide opens the casting guide in a new tab.
- Gallery. Opens the public gallery of designs other people published, in a new tab.
Profile
The top-left drawing: thickness (radius) against distance from the base along the centreline. The solid curve is one side; the dotted curve is the other side, mirrored until you break it.
- Point type buttons (Corner, Smooth, Even, Asym) set how a selected point's handles behave: Corner has none, Smooth eases through, Even mirrors both handles, Asym lets them differ (a sharper turn on one side). Pressing the active type again resets the handles.
- Break makes the dotted (mirrored) side of a point independent, so it can have a different radius from its solid twin. Used for an asymmetric profile, like a glans corona that sits differently front and back.
- Delete removes the selected point.
- Ø in the caption under the drawing is the diameter at the selected point: both sides added. Read only; change it by moving the point.
- Drawing. Drag a point or a handle to reshape the curve. Shift-click adds a point at that spot, or removes one you shift-click directly. Shift-drag on the background box-selects several points. Arrow keys move the current selection 2 mm. Zoom buttons (−, +, 0) sit at the bottom right of the drawing.
Surface
The Surface button, next to the Profile heading, opens a small popover that reshapes the whole profile in one pass, instead of dragging points by hand.
- Pattern picks the effect: Smooth (rounds the whole profile, Amplitude is how far a neck may thin), Waves, Ripples, Beads (rounded bumps pinched in at a narrow neck, like anal beads) or Sawtooth (repeating bumps along the length, with Amplitude, Period and Width), or Simplify (removes points within a tolerance and smooths what is left).
- Apply reshapes the profile as one Undo step. There is no live preview here; check the profile and 3D view after applying. The panel stays open, so you can Apply again with different settings. Revert undoes only the treatment just applied, and is enabled only right after an Apply. The ✕ closes the panel, and the title bar (☰) drags it out of the way.
Path
The bottom-left drawing: the line the object follows, seen from the side. Drag points and handles to bend it. The base is fixed at the bottom left; its handle sets the angle the shape leaves the base at (straight up by default).
- Straighten replaces the path with one straight line of the same length.
- Smooth rounds every point on the path.
Section (the small circle)
The small panel at the top right of Path is the cross-section, seen end on. It starts round. Drag the orange handle sideways to stretch the section out of the path plane, up to 2 : 1 wide, or squash it down to 1 : 2 flat. The value shows under it. Double-click the panel for round again. The mould still splits in the path plane, so an oval section never locks in the mould. Randomizer makes about one design in three oval.
3D view
The centre panel: your object standing on its base, inside a wireframe box the size of your printer's build volume (set in Printer, below).
- Drag to turn the view, scroll or the orange +/- buttons to zoom, the orange 0 button puts the camera back.
- Colour swatches above the numbers pick a flat colour or one of fourteen base-to-tip gradients. This is for your eyes only: it is not baked into any exported file and does not change the print.
- The numbers under the view (length, body diameter, insertable length, volume, weight) update live as you edit. Insertable is the length past the base flange, and past the balls if there are any. Weight is the silicone to mix, waste included, the same figure as Quantities. The same figures, with more detail, are repeated in the Quantities panel.
- mm / in switches those numbers to inches, fluid ounces and ounces. Only the readouts change; the design, the panels and the files stay metric.
Toolbox: Scale, Flatten, Etch, Shaft, Tip, Balls
A small floating toolbox sits near the bottom right of the 3D view, in that order: Scale, Flatten and Etch (the shape tools), a divider, then Shaft, Tip and Balls (the texture targets). Every tool shows its effect live in the preview; Apply keeps the change as one Undo step, Cancel (or Esc) puts the shape back as it was. A panel stays open until you press Apply, Cancel or Esc — clicking elsewhere never closes or loses it, so you can turn the 3D view to check the result before deciding. Drag a panel by its title bar (the "☰" handle) to move it out of the way of the model.
Flatten
Cuts a flat chord into one or more sides of the otherwise round cross-section. Runs before Shaft, so a relief such as the tentacle-sucker pattern sits on the flat bed instead of the round body.
- Top, Bottom, Left, Right. Tick any combination. Top and Bottom are the two sides in the plane of the path (front and back); Left and Right are the two sides out of it.
- Amount (mm) is how deep the cut goes, shared by every side ticked. It never cuts past a 5 mm radius, so a thin neck is never cut through.
- Start, End, Fade zone the flat along the length the same way Texture does: Start and End as a percent of the length, Fade as a length in mm over which the cut grows in at each edge of that zone.
Balls
Off by default; the checkbox turns a pair on. They merge into the shaft and the base flange as a plain union: no smooth blend, no more than two balls.
- Distance (mm) is how far up the shaft from the base they sit. Offset (mm) moves them forward or back in the path plane, negative allowed.
- Gap runs 0 to 100: 0 fuses the two into one ball, 100 lets them just touch.
- Size X, Y, Z (mm) set the shape: X across the plane, Y along the shaft, Z front to back. Lock the three sizes together scales all three at once, keeping the ratio, instead of stretching one axis alone.
Some templates (Realistic, Realistic with glans, Horse, Bull) start with a pair already on, and Randomizer adds them to about 4 in 10 designs; the panel edits whatever is there. Their own texture is set through the same texture panel: the Texture… button inside this panel opens it targeted at the balls (start/end/fade then read pole to pole), separately from the shaft's texture. A sphere has no flat UV map, so this Texture button shows only six patterns picked or built to still read cleanly on one: Hairs, Veins, Wrinkles, Pimples, Pores and Creases (Hairs, Pores and Creases exist only here — see Shaft below).
Shaft
Lays a relief over part of the length. Carried into the object files and into the mould, so the finished mould reproduces it. The same panel is shared by three independent targets: the Shaft button in the toolbox (design.texture), the Texture… button inside Balls (design.balls.texture), and the Tip button below (design.tipTexture) — same controls throughout, only the target differs. The shaft and tip pick from all twenty-two patterns; the Balls picker narrows that to the six built for a sphere (see Balls above).
- Pattern picks from twenty-two: pimples, spikes, bumps, balls, grooves, pyramids, diamonds, hexagons, woven, diagonal ridges, vertical lines, cross, veins, scales, wrinkles, leather, warts, coral, tentacle suckers, hairs, pores, creases.
- Height (0.2-6 mm) is how far the relief rises, or sinks for a groove-style pattern.
- Tile (up to 100 mm) is the size of one repeat.
- Start, End, Fade zone the texture along the length: Start/End as a percent of the length, Fade in mm at each edge of that zone.
- Stretch spreads the pattern wider round the body: fewer repeats, wider lines and veins. Pushed far enough, the pattern shows less than one full repeat round the body and a seam appears; Mask (below) can hide it.
- Twist leans the pattern so its lines run at an angle, or follow the shape's own curve.
- Spin turns the pattern's start point round the body.
- Mask hides a slice of the pattern, leaving 360 minus the Mask value showing, starting at the Spin point; the hidden slice turns and leans with the pattern. Mask fade softens both edges of that slice so the pattern blends out instead of cutting off sharply; it only does anything once Mask is above 0. Spin and Mask together isolate a single vein or line.
- Rotate is a slider that turns the whole pattern in 45° steps, 0 to 315. One control, shared identically by the shaft, the balls and the tip. Invert sinks a raised pattern (and raises a sunken one).
Fine detail is hard to print and to pull cleanly out of silicone: anything under 1 mm is flagged in Checks. Deep or sharp patterns (spikes, coral) are the ones to demould slowly.
Tip
A second, independent texture layer (design.tipTexture), summed on top of the shaft's own texture rather than replacing it — pick both a body pattern and a tip pattern and both show. Opens the same texture panel described above, preconfigured to the last 15% of the length near the tip (Start 85%, End 100%) with the Vertical lines pattern, but every field is adjustable exactly like the shaft's. Meant for a glans ridge or a crease: Vertical lines gives one ridge or groove running the length (Spin plus a narrow Mask isolates a single line at any angle round the tip), Cross gives a crossing pair. Counts toward the feature-size warning and the mould envelope the same way the shaft's texture does.
Scale
Resizes the whole design by a percent, applied to both the profile and the path.
- Width, Height sliders, in percent; plus makes it larger, minus smaller.
- Lock keeps width and height moving together, so the shape's proportions do not change.
Core Cavity
The top panel on the right. It leaves a hole in the base for a Vac-U-Lock plug or a bullet vibe. Off by default. The panel starts folded; its header shows the pin size, or None. Click the header to open it.
- Pin picks None, Vac-U-Lock, Bullet vibe or Custom. The preset sizes are estimates from retail listings; measure your own insert.
- Diameter is the hexagon's width across the flats, 6 to 40 mm. Length is how deep it goes into the object from the base face, 10 to 200 mm. Changing either switches the preset to Custom.
- Once Render has run, the mould downloads carry two more pieces. The pin is a T: its arms rest on the rim of the pour opening and the hexagonal pin hangs into the cavity. Centre it by hand before the silicone sets. The core is the same hexagon, 6 mm shorter and without arms, for TPU: drop it in the hole and cover it with silicone, or fill the hole with a firmer silicone instead. All pieces print lying on a flat side.
- Checks warns when less than 4 mm of silicone is left round the pin, and blocks the mould when the pin would come out through the side or the tip. A straight pin in a strongly bent shape is the usual cause.
Squirt tube
The panel under Core Cavity. It casts a silicone tube into the toy, from the tip to the back, so a syringe of lube squirts out of the tip. Off by default. Folded at first, like Core Cavity; the header shows the tube size, or None. With a tube on, the 3D view shows two dark holes where it comes out: one on the tip, one on the back, at the Exit height.
- Tube picks None, 2 x 4 mm, 3 x 5 mm or Custom: inner x outer diameter.
- ID is the inner diameter, 1 to 6 mm. OD is the outer diameter, 2 to 10 mm, and must be more than the ID. Changing either switches the preset to Custom.
- Exit is how high above the base face the tube comes out of the back: 3 to 80 mm, 10 by default. A value out of range is clamped, with a message. A pry slot on the back that the side channel would cut through is left out.
- The mould gets two channels on the parting line, each 0.1 mm under the OD so they grip the tube: one out through the tip, one out of the back at the Exit height. The back is the outside of the curve. Nothing extra to print.
- Before you close the mould, push the tube out through the tip channel, lay it along the cavity and out of the side hole. Pour. After the cure, cut it flush at the tip.
- Checks warns under 3 mm of silicone round the tube, and blocks the mould when the tube is wider than the toy. With a core cavity the tube runs up the back past the pin, and Checks blocks when there is less than the OD plus 4 mm between the pin and the back.
Checks
Lists problems that would break the mould or tear the silicone, each with what to do about it. Fix everything flagged before you render.
- For anal use. Tick it if the design is meant for anal use; it adds a check that the base flange is wide enough to stop the toy being drawn in fully. See safety for why that matters.
Get the mould printed
The highlighted box under Checks and the Render button. If you have no printer, I print the mould for you in PLA, on a professional printer, and ship it from Europe. Silicone and colour are cheap on Amazon.
- Prices go by the length of the toy: small up to 120 mm $25, medium up to 180 mm $40, large over 180 mm $60. They cover material and print time. Shipping is extra and depends on the country. The line under the prices shows the size and price of your design, and the matching row is highlighted.
- The mould must fit my printer, a Bambu Lab H2S (340 x 320 x 340 mm). When a half is too big, the line turns red and both order buttons are off until the design is shorter or thinner.
- UV resin coating, +$15 adds a thin coat of UV resin on the cavity, for a smoother, glossier toy.
- Order by email opens the Publish dialog. Once the design is in the gallery, your email app opens a message to me with the gallery link, the size, the coating and the price. Add where to ship it and send. The design stays public in the gallery.
- Order privately publishes nothing. It downloads the design file (.json) and opens the same email, which asks you to attach that file. Attach it, add where to ship it and send.
Render and Download
- Render designs the two-piece mould around the current shape: a hexagonal block split along the centre line, with registration pins so the halves only close one way, grooves for rubber bands, pry slots to open it after the cure, and vents where air could be trapped. See mould basics for what each part is for.
- Object STL, Object 3MF download the shape itself (a positive), for printing the object directly rather than casting it.
- Mould STLs, Mould 3MF, Print sheet appear once Render has run. The STLs are one file per half, plus the pin and its core when Core Cavity is on (2 or 4 files; the squirt tube adds no files, only two channels in the halves); the 3MF carries every piece in one file, with Bambu Studio's ironing option checked for the parting faces. The print sheet lists how much silicone and filament the design needs, and which way the halves close.
Printer
Pick a printer from the list, or type X/Y/Z directly. Sizes the wireframe box in the 3D view and checks the object and mould both fit inside it. Folded at first; the header shows the printer, or Does not fit in red when the mould is too big for it.
Quantities
Folded at first; the header shows the silicone mass to mix. Silicone mass to mix (with the waste allowance), split into part A and part B by weight at the mix ratio you set, the size of one mould half, and an estimated filament use for printing it. Open Assumptions to change the mould wall thickness, silicone waste percent, mix ratio, silicone density or print infill that these figures are based on. See how much for the reasoning behind the defaults.
Gallery, Publish and Share link
- Gallery opens the public gallery of designs other people have published.
- Share link publishes the design the same way and copies a link to it. The link opens the design straight in the tool.
- Publish sends the current design's file (its shape, colour and texture, nothing else) to that gallery under a random two-word name. It cannot be edited or removed afterwards, so check the design first. See the guide's privacy and terms for what is and is not stored.